How to Use a Pumice Stone Safely and Effectively

Pumice stones

Pumice is created when lava and water mix. That the process traps gas bubbles in the hardening material, resulting in a porous and abrasive stone perfect for sloughing away dead skin. In addition to its primary purpose of exfoliating skin, you can also use pumice to remove dry skin or excessive hair, remove pills from fabric, and even clean your toilet.
You can use this stone daily, but it’s essential to know how to use a pumice stone properly. If you’re not careful, you can remove too much skin, cause bleeding, or increase your risk of infection.

How to Use a Pumice Stone

These step-by-step instructions will help you to remove your rough skin properly. If you begin to feel pain or irregular symptoms, stop using the pumice stone immediately.

Preparation

  • Assemble all of your elements in one place. Make sure that your pumice stone and water are clean.
  • The usual standard part of the body to exfoliate with a pumice stone is the feet. Dip your dry, callused skin in warm water for 5 to 10 minutes because it will help to soften your hardened skin. Add soap or glycerine to your water for additional softening and to improve moisture. But if you’re want to use a pumice stone on your elbows, knees, or face, complete this step in a warm bath or shower.

Using the pumice stone

  1. While you’re soaking your skin, also wet your stone in warm water. Never practice a dry pumice stone on your skin. Wetting the stone will support it to slide more easily across your skin, rather than catch on it, and reduce your risk of injury.
  2. Wait until your dry skin has softened, and then remove the target area from the soap bath and pat dry with a napkin. The skin will be more comfortable to remove if it’s soft and supple. If your skin is still rough, soak for several more minutes before patting your skin dry.
  3. Remove from the warm water and apply the pumice stone on your targeted skin.
  4. Rub the abrasive side of the stone gently over your skin in a circular motion with light pressure. Continue until you remove the dead skin and get to the fresh, supple skin underneath. If the skin is soft, it should start coming right off. If your skin begins to feel painful or sore, stop because you’re most likely using too much pressure.
  5. You notice your heels for your feet and the sides of your toes, and other dry areas you recognize.
  6. After several minutes of light rubbing, wash your affected skin and your pumice stone. And take a look to see if you need to keep going. If you still see spots of broken skin, repeat this process. Continue using the stone daily or a few times a week until you’re satisfied with the results or maintain soft, supple skin.

Finishing up

How to use a pumice stone

  1. When you’re done, use a napkin to pat your skin dry. And apply a moisturizer or glycerine to your skin to maintain moisture and keep your skin soft.
  2. Do not share your stone with other people. Each family member should have their own.
  3. After regular using your stone will become too smooth to remain effective. If your stone becomes too small or soft, replace it and find a great selection of pumice stones.

How to Use Pumice Stone on Face and Neck

The face and neck are susceptible areas of our body. If you practice too much pressure, your skin glamor can be reduced and cause redness. To use a stone on your face or neck, consider buying a double-sided pumice stone for face.

Follow the same steps as above. Instead of using the rough side of the pumice stone, use the softer side. Rub the stone in a round motion for about a few seconds. If you notice to feel any burning, stop using the pumice stone instantly.

After removing your rough skin, clean your face and neck with warm water, use a napkin to pat your skin dry, and apply a moisturizer lotion. You can also use Aloe vera gel for skin brightness. Only use a pumice stone on your face once per week. Besides, you can want to use a pumice stone for your baby’s skincare.

Pumice Stone for Hair Removal

Besides, a pumice stone can also remove undesired hair.

You can follow these tracks for hair removal:

  1. Soak your skin in warm water for 5 to 10 minutes.
  2. Also, wet your stone in warm water for several minutes.
  3. Rub soap lather on your skin.
  4. Then rub the stone to your skin in a round motion with gentle pressure to remove hairs.
  5. Wash and repeat until all hair has been removed. If you notice any irritation, stop using it.
  6. When you’re finished, wash entirely with warm water to remove any excess hair or skin.
  7. Use a moisturizer on your skin and repeat this method every few days until all hair has been removed.

Use It to Remove Pills From Clothing

How to use a pumice stone

The soft, porous surface of pumice is perfect for taking pills and lint off of clothes. If you have a sweater you’ve been wanting to clean up, lay it on a flat surface. Brush a dry pumice stone over the pills in a round motion. Don’t roll too hard, because you don’t want to damage the fibers of the garment, gentle pressure is all that’s required to take the pills right off.

How to Use a Pumice Stone on Toilet

Pumice can be used to remove copper rings from the inside of a toilet.
For your better experience, we recommended a video tutorial to clean your toilet properly.

You can practice the stone in combination with toilet cleaner for more stubborn stains. Be sure to use separate stones for toilet cleaning and body use. Do not use the same stone for both purposes.

How do Pumice Stones Work

A pumice stone is formed when lava and water mix. It’s a light-yet-abrasive stone used to remove dry, dead skin. This stone can also soften your calluses and corns to reduce pain from friction. The rough side of the stone removes your dead skin smoothly like a haircutter machine. If you use it properly, it doesn’t have any side effects.

How to Clean a Pumice Stone

  1. Dead skin will build up in the stone’s pores as you use it, so you’ll need to clean the stone after practice. Use a brush to clean the stone while holding it under running water. Add a bit of detergent to help clean the stone thoroughly. This way, your stone will be clean and ready for next use.
  2. If you’ll want to give the stone a deep cleaning to make sure it isn’t hiding bacteria. Bring a small pan of water to a full boil, drop in the stone, and boil it for five minutes. Use tongs to remove the stone from the water and allow it to dry completely. If you use the stone regularly, boil it every two weeks to ensure it stays clean.
  3. Set the pumice stone in a dry place to completely dry out so that it doesn’t stay damp in between uses. If you let the stone stay wet, bacteria could grow in the pores, making it unsafe to use.